The bioactive CPS component makes up 70% of the putty by volume. The binder improves handling and aids in maintaining the space between the particles, which facilitates revascularization after implantation. It is composed of calcium phosphosilicate (CPS) particles in a bimodal size distribution combined with a polyethylene glycol and glycerine binder. Place Access Gold low viscosity impression material in an automix syringe and inject directly into a clean, dry, retracted sulcus preparation using an Access intra oral needle tip (REF 290017).NovaBone® Dental Putty is 100% synthetic and fully resorbable.With a surgical rongeurs or coarse grit acrylic bur, remove all interdental flash and/or undercuts.Place loaded tray in patients' mouth - allow to remain stable until set.
#Dental putty code
Remove equal amounts of Base and Catalyst from the jars using the supplied color code scoops.Seat the loaded tray into the mouth allow to remain stable until set.Place Access Gold low viscosity into an automix syringe and inject directly into a clean, dry, retracted sulcus preparation, using an Access intra oral needle tip (REF 290017).Shape to fit into the desired tray, which has been pre-treated with adhesive.Mix by kneading together for 30 seconds until no streaks are visible.Remove equal amounts of Base and Catalyst from the jars using the supplied color coded scoops.Note: Do not mix putty with latex gloved hands! Seat the loaded tray into the mouth - allow to remain stable until set.Inject Access Gold low-viscosity or Access Monophase directly into a clean, dry, retracted sulcus preparation, using an Access intra oral needle tip (REF 290017).Access Heavy, Access Monophase or Access Purple may be selected, depending on the application. Express Access Impression Material into a prepared tray, pre-coated with adhesive.Contact with latex gloves, hemostatic agents, hand lotions, eugenol or sulphur compounds may interfere with the setting properties of Access Impression Materials.
Allow to air dry for five (5) minutes before using. Note: For faster procedures, it is advisable to use two (2) mixing dispensers.Īlways apply a thin layer of Access Impression Material Tray Adhesive to a clean, dry impression tray. Any of the viscosities will chemically adhere to another viscosity, permitting a wide range of possible techniques.
Special hydrophilic surfactants have been added to Access Impression Materials to allow them to be highly wet table in a moist environment. The material is odorless and tasteless, and may be soaked in common disinfecting solutions without distortion. Highly accurate and stable, Access impressions may be poured immediately or up to two (2) weeks after the impression is made. 3 Load the tray with impression material and take the impression.ĪCCESS IMPRESSION MATERIALS (VPS - VINYL POLYSILOXANE)Īccess Impression Materials are addition reaction silicones which offer excellent physical and dimensional properties. Instructions for Use: 1 Apply a thin layer of Access ® Tray Adhesive to the tray using the applicator brush. A polyether adhesive must be used for polyether impression materials. NOTE: The adhesive does not always secure sufficient adhesion to trays made of other plastic materials or individual trays made of base plates. Or change to a Heavy/Wash technique, using Access Gold for the Wash and Access Purple, Heavy or Monophase for the Heavy VPS material. It is better to place both materials at the same time, which is technique sensitive.
The removal of the set Putty causes the distortion, which may be called out by the lab. When would using Putty cause distortions in Impressions?Ī distortion can take place in a Putty/Wash impression technique when the user takes the putty impression PRIOR to placing the Access Gold or similar wash VPS material. The hub is green (also called teal) and the mixing element is natural or clear. The internal diameter is 6.5mm it has 11 elements and a straight end. The Access VPS impression materials uses 1:1 automix nozzles. What are the specifications for the mixing nozzles? The scoops VERY generously use the materials, and would be overkill for a 3 unit impression.
#Dental putty full
If you are making full mouth impressions, expect to get 25 from one finished goods. (2-3 finger full worth of materials each) If you are making 3 unit impressions, expect to get 50 to 75 from one finished goods. How many impressions will I get from Access Putty? A wash in this case is a low viscosity VPS material like Access Gold. You can use Access Blue in a tray with a wash. Can I use Access Blue in a tray with a wash?
0 kommentar(er)
